Synthetic two-cycle oil
- Thread starter Jersey Jeff
- Start date
THEFERMANATOR
God
He's not running a conventional 2 stroke oil though, so don't mix 100:1 on regular 2 stroke oil. AMSOIL makes there saber oil that they say you can run a t100:1 in 50:1 engines without damage, but many have blown there engines running it this way and is why I never tried it.
captpete13
Senior Member
That's the same stuff I got.
Genie Aye, If I had a high tech motor like an Opti or an Etec I would run a better oil. But my motor is a 1990 225 carbed Yamaha. And I use a lot more that 5 gallons a year. If I puke a rod because of lack of lube I will go back to Yamalube.
I hate to tell ya Ferm but HPDI's require the same Yamalube that every other yamaha requires, 2M. It's nothing special, no magic going on there just 6 oil lines, one behind each reed block. There is also a little fed to the vst to lube the fuel pump and that's it
THEFERMANATOR
God
It's still best to run a DFI oil with ring free and anti-varnish build-up in it. That was one of teh HUGE downfalls of teh early FICHTS was the use of regular 2 stroke oil and the carbon build-up that came with it.
No need to be confused, I am indeed running Amsoil Saber Outboard premix at 100:1 and have had no problems. I also only run pure gas at 90 octane, and do not put any ethanol blend in any of my motors. Here is how good Amsoil is in my experience; I ran my 2003 Ski-Doo snowmobile, 700cc mototor, about 135HP, clean out of oil and was running about 80MPH across a hayfield in northern MI, turning about 7800rpm on the tach. (The out of oil part is a much longer however embarrassing story). The motor seized at 80MPH as I was thrown into the handlebars and came to a dead stop; the motor locked up tight. I had Amsoil Interceptor 2-stroke oil in the motor. After about 10 mins the motor came lose and I drug the sled home, tail between my legs. At home tearing down the motor, I all had to replace was the mag side piston rings and hone that cylinder. NO scuff on the cylinder wall or piston, and the PTO cylinder was just fine. Amsoil as a lubricant is just that good, and is arguably the best synthetic on the market, not to mention they have been doing it the longest. They also have a tremendous engineering department that welcomes challenges to the quality of their product in addition to claims of failures and burn downs. I think the claim that that has been many burn downs using Saber outboard at 100:1 is false. Lots of folks run it up here.
Genie Aye
Junior Member
I have had my Doo 1000 do the same thing---brought it home--new rings and pistons(for saftey) and put her together and got another season before selling the sled-----But I was running ----Redline full synthetic race oil. Any quality oil will do the job---in 40 years--I have seen very few oil related faliures from the lubricant.
reelapeelin
God
I'm pre-mixing w/the 2.4 Merc...just getting finished w/a tank of fuel w/Pennzoil Synthetic BLEND...and have two gals of Merc oil to follow on next fill...the Merc oil is 19.99 at Academy Sports all the time...
Union Laker
Member
We are always running WOT in the 19' Starcraft. only a 800 Redstripe, I use the full synthetic like the smokeless attributes of it . I mix 16 oz to 10 Gallons & run Sunoco 93 Octane. Either Lucas or Penzoil. works good .
Running around the inland lakes have to get to where your going.
Out on the Great lakes we run 3/4 throttle. around 30mph.
Running around the inland lakes have to get to where your going.
Out on the Great lakes we run 3/4 throttle. around 30mph.