Just wondering: I am in the middle of tearing down my V20 .... and considering all the fixes I want to make. One thing I am getting too old for ... is banging my knees on the gunnel as the boat rocks while fishing. For all the upgrades I have seen at this site - I havent seen padding yet on the sides. Has anyone done this ? Know of a place to purchase at a reasonable price ? Any guidance would be appreciated. Thanx.
Gunnel cushions for the knees
- Thread starter brianct12
- Start date
B-man, I ran across some in one of the chain catelogs, Overtons or Boater's world. I think 84 in was the length.
Other than that, it's up to finding a local canvas shop & there's no tellin how much or what the quality would be like.
you could even make some yourself with some pvc-foam board, vinyl. Just make sure its a closed-cell foam for cussion.
Some of the new boats have them slid into clips and then snap just under the gunnel. Another option, if their made with a hard board is to through bolt with Brass hardware (never rust), the lower quality SS from hardware stores will eventually surface rust.
Best of luck with your re-work.
-JohnD
Other than that, it's up to finding a local canvas shop & there's no tellin how much or what the quality would be like.
you could even make some yourself with some pvc-foam board, vinyl. Just make sure its a closed-cell foam for cussion.
Some of the new boats have them slid into clips and then snap just under the gunnel. Another option, if their made with a hard board is to through bolt with Brass hardware (never rust), the lower quality SS from hardware stores will eventually surface rust.
Best of luck with your re-work.
-JohnD
shicks007
Senior Member
I'd like to install some in my boat also. The new Boter's world catalog has them in there. Emmitt Fitzpatric's boat in the Gallery has them also.
http://www.wellcraftv20.com/gallery/view_photo.php?set_albumName=album06&id=b2
Good Luck,
Scott
http://www.wellcraftv20.com/gallery/view_photo.php?set_albumName=album06&id=b2
Good Luck,
Scott
Brianct12, Up intill this year all the catologs carried coaming pads that were towide to fit our boats and way to expensive. Last year I had a local guy make me a set cost about $240. This year Boaters world has 36" -$64.99 or 48" - $69.99 in length X4 1/2" high and 2 1/4" thick on page 334. These look like they will work just nicely. Just priced toe rails from a fabricator $340. ouch no way, I can make them out stainless tube and stantions from any boaty store or PVC. All boats should have more grabe rails, coaming pads and toe rails sweet! Crusher
fillet1
Junior Member
A toe rail lets you hook your toes under it so you can lean over the gunnel without going overboard. Its a rail like a bow rail at the floor of the boat.
Some boats especially larger sportfish have wide gunnels that hang over the edges of the cockpit. That way, when you lean over the gunnel to wire a fish etc your legs are against the gunnel, but your feet are UNDER the gunnel. You stay more stable that way.
On other boats like the v-20, the gunnels do not extend out over the cockpit. Instead you lean up against the walls of the boat/sides of the hull. Your toes are also against the hull/sidewall. This makes staying in the boat difficult and its easy to loose balance. Toe rails give ya something to hook your toes under to counteract this.
Some boats especially larger sportfish have wide gunnels that hang over the edges of the cockpit. That way, when you lean over the gunnel to wire a fish etc your legs are against the gunnel, but your feet are UNDER the gunnel. You stay more stable that way.
On other boats like the v-20, the gunnels do not extend out over the cockpit. Instead you lean up against the walls of the boat/sides of the hull. Your toes are also against the hull/sidewall. This makes staying in the boat difficult and its easy to loose balance. Toe rails give ya something to hook your toes under to counteract this.
Mac_Attack
God
Yoy dog MJ! Careful CB! Bill Mc ;D