Search results

Guys I hate to do it, but we might be loosing our house. My V20 is separated, needs stringers, and transom. Deck is good hardly any soft spots. Trailer needs hubs on all four to be safe. I have a title for the boat. I have stripped 90% of the bottom paint, all the transom is removed. I am...

Aight guys and gals. My V20 has been split with the hull in the garage and cap in the yard on a stand. It needs a new transom and new stringers. Needs a motor. Might as well say I need a trailer. Dad always loved the boat so its hard to take it all to the dump. The floor in the cap looks to be...

Are these any good?? For the price I am wondering just how bad it is. http://pensacola.craigslist.org/boa/4553512990.html

I have a 1992 Evinrude V4 90hp outboard I have been working on for a school project. Just thinking 18-24" setback floatation bracket, would twin 90s be too much weight?

86 250 Sportsman Twin 86 150 Yamaha's Galvanized trailer No title. The previous owner bent me over good...... Outboards had good compression a couple years ago. Trailer needs springs, and tires Boat needs a little bit of work. I want it gone. Someone make an offer. Jason 8507232284 Will...

I am building a mud quad, 2003 Honda Rincon. I want to build a fiberglass box for the rear rack. Three compartments. One in the middle being an insulated cooler big enough to hold a 12 pack of Bud Light and ice. The compartment on each side of the cooler will be for storage of straps, shackles...

Not that I can afford one, but how do y'all think this newer 4 stroke will work on a V20?

A good friend just bought V6 Evinrude 150 with 200carbs. It lowers and trims down. But will not trim or tilt up. The electric trim motor does run. If we pull up the motor the trim rods will extend but will not push the motor. Its got fluid. What are we missing?

We fished public numbers within two miles of the beach. Five yaks total. Launched at 8:30pm and landed 5am. Biggest snapper was 33". Here is my haul. Redfish is 26 3/4".

Replaced starter in January i think. Thread on here somewhere. Now it clicks and that's it. also blowwing ignore 1 fuse. I hear a thunk ever time i replace it. Sounds like it comes from starter. Any advice? Just cleaned connections and about to drop starter. Sitting behind Papa John's now and...

Sitting together on a train were Pres. Obama, George W. Bush, a little old lady, and a young blonde girl with large breasts. The train goes into a dark tunnel and a few seconds later There is the sound of a loud slap. When the train emerges from the tunnel, Obama has a bright red hand print...

I sold my Merc. Hated to do it. Onto new things. I just started a Marine Tech class. So far I enjoy it over welding. I need some opinions on a motor or motors for my V20 when I get it done. I was thinking twin 90ish's? I am leaning towards Johnson and Evinrude. Maybe a 225 Ocean Runner? So far...

Got a guy coming to look at the Mercury 200. I told him. Would pick up a impellor. Installex it and no water. Pulled foot. Impellor stuck on shaft. Has rotational play but wont slide up. Need to get this thing off!!!!

25" shaft. New stainless tilt tube. Needs water pump and carb cleaning. Cowling in good shape. Asking $1500 obo. Jason 8507232284

Are we on forum runner?

http://www.copart.com/c2/boat_auction_search_results.html?_eventId=getLot&execution=e4s2&lotId=28709002&returnPage=SEARCH_RESULTS 1975 Wellcraft V20 center console I/O up for auction in Salisbury MD

I bought this boat last year. Its a 1982 Wellcraft 18 Fisherman. I discovered stringer rot and every one needs to be replaced. The previous owner replaced the transom and cut the cap in half to access the transom. They did a halfass job repairing it. The cap needs to be repaired correctly and it...

Well, my boat is in pieces scattered all the over the yard. The 18 Fish is a hopeless case. I have considered buying another hull to rig out but then I end up with yet another boat in the yard. So today I went down and dropped the down payment on a new boat. She is four feet shorter than the V20...

I have the lower unit I bought for the 250 Sportsman and removed. It fit a 1986 Yamaha 150 25". L150ETXJ. What else will this thing fit? Trying to sell it for $350 to cover a surgery. Any help is appreciated. I found the emails where I bought it and all they say is the powerhead blew due to...

How would arjay pourable ceramic compound work for repairing rotted out stringers?