Search results

But still a large step below the Hyd steering for sure--1 finger steering year after year rocks.

The 3m wheel does the job, but makes a mess. I strip the old stripes off with a heat gun and a plastic razor and then clean the gum off with Brake Clean on a towel--works well--in fact real well. Now remember--after that striping being on there for 20+ years there is going to be a shiney and...

Reading Jetty Rockers experiance and adding my experience--I would say a 13 3/8" by 15" stainless Yamaha SSW prop would allow you to get up on plan quickly and haold the plain with a load. If you have a good prop shop or dealer they will let you try different props before you buy--as long as...

More pictures

Was 53.4 on GPS--before install of the full top and radar arch--cost me some speed--run around 49+ loaded for fishing with top up. As far as weight--no issue--but a 2.6 versus my 3.3litre would be a little lighter and handles the 3.3 fine and handles great compared to the ole 175 johnson and...

Here was my remedy for the exact same issue---with my Cox--I did the same thing--I adjusted the rollers everywhere--this is how I handled it--and it works--I power the boat on after sinking the trailer a bit over half way and it centers every time. First I mounted the boards and covered off of...

The 200 ho is a hp monster--does not need much throttle--With the difference in the 2 boats between my 20 and the 21 with the transom set back a bit--I would say yes--a great choice is you need alot of power--I would probabley go with the small 200 instead if you can get a better deal on one...

Yes--a cleaning /bait station with wash down hose. The pictures with the boys cleaning fish---#1 picture Neah Bay,Wa. #5 picture LaPush,Wa. Thanks!!

If I had 100 comp on any cylinder and it is more than 10% lower than my highest---bad cylinder/s. With only 100lbs comp--I would wonder what type of freshen up your mechanic did--almost sounds like some ports may hooked the rings from burr's. I can tell you with a injector out on my...

Here are a few shots of the boat as being changed up for our fishing---more to come.

I have dealt with Bennet in the past--not such great CS or backing of their product--I know they have changed their buisness practice the last couple years because of lost buisness Like me. As for the Lenco letting go--I have never heard of this--must have been a freak thing--cause I beat the...

Actually I have back to back seats on both sides right now---and they work well. But I have a Seat out of a 07 Kenworth and waiting for the other seat and I will be putting those in--true air ride---then putting 2 other seats in--probabley just like the babck to back seats are now. Project...

Yes I love my V-20 since I put on my Lenco trim tabs---a great investment!!

Chris Craft would use other Manufacturers from time to time for hulls---is this the case here?? Maybe. I know that CC used Uniflite Hulls in 2 of their rare but much wanted models.

Wish I had some extra money to buy this---that would be a SWEET boat when done---especially with a outboard on it!!

There is no question that the 225Optimax is strong--the Optimax series fro Mercury is probably one of the best they have ever built and strong---What is was after was 218 vs 225hp is not enough to make that speed difference. Maybe it is just the way my V-20 is set up and the water is was...

The Optimax is not going to give you 55 to 60mph---besides--you do not want this boat that fast--When I had mine at max around 53 fully trimmed out--it is getting scarey--40 to 45 is real comfy. The Big 200ho E-Tec is actually 218 at the prop--so a 225 will not do it--LOL. The reason I said...