Search results

Thanks Cam Will check them out for later, Listing states 1" tubing. My Bimini frame is 7/8", maybe will tighten down.

Thanks, D

Yeah I believe I asked the question, about them a while ago (on here), about the deck drains. wanted to have them drain overboard, but are too low. Drain into bilge now. No plans to raise deck at this point yet. Have to replace the wood Battery box shelfs, because of all that water coming in...

Oops, screwed up replied twice, sorry.

Yeah I noticed the difference's in the liners into the 80's There is ALOT of things changed when the 80"s boat were made. I was looking to add Teak Step pads on my gunnels. But I don't have the wide flat top area. Like Cams boat is. my top area is raised, and is only about a 1-1/2" wide...

Yeah I noticed the difference's in the liners into the 80's There is ALOT of things changed when the 80"s boats were made. I was looking to add Teak Step pads on my gunnels. But I don't have the wide flat top area. Like Cams boat is. my top area is raised, and is only about a 1-1/2" wide...

Thanks Guys, Gives me some idea what they looked like. But were NOT mounted in any ONE, Standard Place,,,, Hey Cam, like the Rod Holders attached to Bimini Frame. Look like Stainless. Were they custom made, or available from a Vendor ?

Thanks "D". When you get it uncovered, and you remember, Please send a Pic, would appreciate it. Just have never seen this "Factory Extinguisher Compartment" in any V20 photos. (and I have a Bunch !!) Curious to see what you have.

Found this one, Plastic and a bit cheaper. https://www.fpmarine.com/Paragon-Plastics-Fire-Extinguisher-Insert-Holder-p/plastics10048extinguisheroffwh.htm

Boy that's a Pricey item... ($157.00 w/o Extinguisher) Made out of Starboard !! Have you seen any V20's with that (or similar) installed by factory. I'll have to check the Gallery photos to see I spot any. Thanks for the Reply.

Don't feel bad, I don't get email notifications either, and checked the box for them. If I don't check the Forum, would never know i got a reply.... Thanks for your reply.

Question , This is stated as "Standard Equipment" on the V20 Brochures ? Where is it , or should it be located ? I have a small Dry Chem Ext. mounted on the cabin interior wall. Sure don't have a recessed compartment for a Fire Ext.

Thanks 3 Squids Good idea Flush handle. was that there from Wellcraft, or installed by you ? Mine has one on the front lower, also which looks like factory, as I have seen alot of earlier V20"s with one there. So is spray foam, mine is just raw resin covered wood and glass. Did Wellcraft...

Thanks Guys Marks on rear Top of motor box WAS from a Handle Previous owner must have installed. Had "Stainless Straight Blade screws " Self tapping that were cut off flush. Never saw a handle installed like that, just the flush ones, like a another guy mentioned. But a handle is needed there...

Need some Help ! Motor box on my V20 seems to be missing pieces. Aluminum piece on rear wall appears to attaches to nothing! No seals of any kind along sides ? No Latches to hold down ? No Insulation or sound deadener in side ? Don't have another V20 around, to compare, so hoping someone can...

Bow Rail Thank for checking, But I will have to Pass on them. Having Vehicle problems (Front Hubs), so could not get this weekend anyway. Was trying to figure out how to fit in a Malibu 4-door, anyway. See if "StepliftV20" is still interested. Mine IS solid across front., Just Aluminum...

Bow Rail PM Sent, Thanks

Bow Rails Too Bad your in SC. Very long drive from NJ. Too big to ship, and $$. Is yours welded, or does it has separate fittings ?

Can anyone confirm that Wellcraft built the older V20's with Stainless Bow Rails ? . Brochure I've seen states that the Rails were Stainless, BUT mine appear to be Aluminum, with Zamak Rail Fittings. Just like the Cockpit Railings. All my Rail Fittings and Cleats are the crappy Zamak, and are...

Seller marked it as SOLD !!