Gallery :: Wellcraft Project

Wellcraft Project

Comments for this Album

Gallery: Gallery

Album: V20 Center Console

Album: turbinedoctor 1984 CC

Album: Wellcraft Project

Bringing Boat Home

New Bow ladder folded up

New Bow ladder down showing mounting hardware. Polished all bolts and washer myself.

Ladder still colapsed

Ladder extended

Installed new latches on the seats

New radio and old fish finder

Revarnished hatch

1984 Merc 90 hp inline 6

Bait board removed

New homemade bait board

From: New Mexico dating site and Nevada free dating for local men and women seeking free online dating Fri Feb 6 20:57:56 2009
Local online free dating in New Mexico and local online free dating in Nevada

From: lbznmobk Thu Jan 27 00:22:41 2022
55Vo7g luihzskuunwe, [url=http://djoecduknxnx.com/]djoecduknxnx[/url], [link=http://niyvmhvwcjgm.com/]niyvmhvwcjgm[/link], http://ypwohwzrvozw.com/

From: markus Mon Apr 18 23:08:28 2022
http://imrdsoacha.gov.co/silvitra-120mg-qrms

From: yqpwqkparv Sun May 15 08:30:14 2022
TiWIXw huhzyfnsqigb, [url=http://wbcdslboauvh.com/]wbcdslboauvh[/url], [link=http://swwqihhlfzxv.com/]swwqihhlfzxv[/link], http://zrdafdvnnmje.com/

Old fish finder sonar routed through plug hole. Not a good idea.

4 MOORE FUN. Kicking around some names for my boat.

V20Fisherman 85 Specs

Hatch needs varnish

1984 Tower of Power

Supported to remove springs

Support to remove old springs

Old spring hardware

Cut off wheel works great on rusted bolts

Needed for stainless bolts.

Replacing rusted bolts with stainless.

Old spring bolts and plates.

Axle sprayed with Rust Converter

Cluttered up garage

All cleaned and ready to reassemble.

Pressing in seals.

Repacked bearings and seal installed.

44 inch rock 1 11 07

First rock 1 11 07

Places where roller arms should pivot but don't.

Repacked bearings and installed hub.

New springs and mounting hardware.

Inside of wheel well painted.

outside of roller, shaft and roll pin.

Inside of roller on shaft

Front port side rollers and shaft.

Hole in roller to drive in and out retaining roll pin.

Front port side roller arm support.

Rear port side front roller shafts.

Rear port side roller arm.

Rear port side roller arm support.

New fish finder Lowrance LMS 334 igps

Console with new Lowrance LMS-334-IGPS

Guide on installed. Works great.

Boat guide ons installed. Make loading by yourself easier.

Jack need lubing or replacing.

Two speed winch

Wider bow roller allows easier cable and safety chain hook up.

Stainless bolts holding wheel wells

New jack to replace old one. Lube on old one did not help much

New rollers, hog rings and square bend bolts.

Stern supported to replace rollers.

Rollers removed.

More rusted bolts to replace.

Grove cut into roller arm.

Ready to remove rusted roll pin, washers and old roller.

This roller was completely froze in place. What a drag unloading the boat.

Wear marks from boat sliding onto and off the trailer.

Dremel with cut off wheel works great here.

Outter roll pin and roller removed

Cutting off inner roll pin.

Old plastic and steel washers. Maybe I should reuse them, NOT!

Punching out remainder of roll pin.

Quick change cut off wheel for Dremel.

Set of drift pin punches.

Assorted Dremel attachments. Can't have too many.

Out with the old and in with the new.

Spare 90 hp merc for parts, $100

Spare lower unit and a prop to big.:(

Routing of new fish finder sonar. Like it much better.

New pipe lights

Turn light current draw

tail light current draw

Gallery: Gallery

Album: V20 Center Console

Album: turbinedoctor 1984 CC

Album: Wellcraft Project

Powered by Gallery v1